Skip to main content
Call 022 101 8468Get Free Quote

Do I need waterproofing under tiles?

Tiles look watertight, but they are not. Here is what the NZ Building Code asks for, what consent and a PS3 mean, and how to spot a failure.

Yes, in a tiled shower. Tiles and grout are not waterproof, so a membrane goes under the tiles. E3 sets the performance standard and E3/AS1 calls for a membrane under tiles in showers. Other wet areas depend on the design, so check the plans.

What clause E3 says

Clause E3 (Internal Moisture) of the NZ Building Code exists to protect people and buildings from moisture getting into the structure. It also protects neighbouring household units from water damage, and requires wet area surfaces to be impervious and easy to clean.

E3 is a performance clause. It says what must be achieved, and the acceptable solutions and manufacturer systems show how. The E3/AS1 document, for example, calls for an impervious membrane under tiles in tiled showers.

Which areas need a membrane

Showers are the clear case. Bathroom floors, and kitchens and laundries where a wet area membrane is specified, are covered by the Waterproofing Membrane Association Code of Practice for internal wet area membranes.

Not every wall and floor in a bathroom is treated the same, and the rules depend on the lining and design. Your plans or designer will say which areas need a membrane, and we check that against the plans when we quote.

  • Showers, including the floor.
  • Floors and laundries where the plans or designer specify a membrane.
  • An impervious substrate or lining may not need a separate membrane, so check the plans.
  • Balconies and decks are a different case. They are an external moisture matter, covered by clause E2, and need a weathertight membrane with falls to drains.
Read the questions we get about waterproofing

Why tiles and grout are not waterproof

A tile can be impervious, but cement-based grout is not. Water gets through the grout lines and behind the tiles. The membrane underneath is what actually stops the water.

For wet area floors, E3/AS1 also sets a water absorption limit of 6 percent for the tiles themselves. That is about the tile, not the grout, and it does not replace the membrane.

Membrane types

Wet area membranes come as liquid-applied or sheet. Liquid-applied membranes go on in coats and are the most common under bathroom tiles. Wet area membranes are tested to the Australian and New Zealand standard AS/NZS 4858, and suppliers require their systems to be installed by trained or approved applicators, exactly as the system specifies.

Thickness matters with liquid membranes, so the manufacturer system has to be followed. We use ARDEX and Mapei systems, and we are ARDEX waterproofing accredited.

Building consent and who can do the work

Replacing the linings, waterproofing and tiles in an existing shower in an existing home may be exempt from building consent under Schedule 1 of the Building Act 2004. In one 2024 Canterbury case (MBIE determination 2024/054), fitting a new membrane while replacing the linings in an existing home was found to fall within that exemption. Exempt work still has to meet the Building Code.

Consent is still needed if the structure is altered, for example a recessed floor in a slab or changes to framing, or if the number of sanitary fixtures goes up. The owner is responsible for deciding whether work is exempt, so check with your council. Christchurch City Council has an exemption information sheet.

At the time of writing, internal waterproofing is not restricted building work and there is no licensed trade for it, but the rules are under review. In practice, membrane suppliers only stand behind their systems when trained or approved applicators install them.

The PS3 producer statement

A PS3 is a producer statement for construction. The person or firm who did the waterproofing signs it to say the work complies with the Building Code and the consent. Councils commonly ask for it before issuing a Code Compliance Certificate.

We provide a PS3 producer statement for our waterproofing on every job. A PS3 is our statement that the work complies. It is not a guarantee.

Signs that waterproofing has failed

A moisture meter can show that moisture is present, but not where it is coming from. If you see these signs, get the shower inspected before retiling over it.

  • Mould that keeps coming back around the shower or on adjoining walls.
  • Peeling paint or bubbling and bulging wall linings.
  • A damp or musty smell.
  • A spongy shower floor.
  • Soft skirting, swollen architraves, or a door that has started to stick.
  • Mouldy silicone that returns quickly after cleaning.

Want this done properly on your job? See our waterproofing in Christchurch page, or request a quote.

Common questions

Do I need building consent to retile a bathroom?

Often not, if you are replacing existing linings, waterproofing and tiles in an existing home. It may be exempt under Schedule 1 of the Building Act 2004. It is still needed if the structure changes or you add fixtures, so check with your council.

Are tiles and grout waterproof?

No. Tiles can be impervious, but cement-based grout is not, so water reaches the surface under the tiles. The membrane is what keeps the structure dry.

What is a PS3 for waterproofing?

A PS3 is a producer statement signed by the person who did the work, confirming it meets the Building Code. Councils commonly ask for it when finalising a consent. We provide a PS3 producer statement for our waterproofing on every job.

Is waterproofing restricted building work in NZ?

At the time of writing, no. Internal waterproofing is not restricted building work and is not a licensed trade, although the rules are under review. Membrane suppliers still expect their systems to be installed by trained or approved applicators.

Can I retile over an old shower without waterproofing it?

We would want to check the existing membrane first. If it is unknown, or the shower is showing signs of moisture, new tiles can hide a problem. We confirm what is needed at quote.

How do I know if my shower waterproofing has failed?

Look for returning mould, peeling paint, bulging walls, a musty smell, a spongy floor, or swollen skirting and architraves. Get it inspected, because a moisture reading alone does not show the source.

JSR

Let's discuss your project.

Whether you're a developer planning a multi-unit build, a builder coordinating a fit-out, or a homeowner renovating a high-quality space — we'll review your project and reply with a clear, itemised quote.

No obligation·Reply within 1 business day·Free on-site visits across Canterbury